How To replace outer glass lens on Samsung galaxy vibrant

SamSung Galaxy Outer Glass Replacement

Please click on the below two links of video which will demonstrate how to replace the outer cover of galaxy S. if you are not comfortable doing it, give it to Samsung or other mobile services store as they are the best ones to do the same.

Video 1
Video 2

Please Note

The outer glass lens is actually the digitizer. It sits just in front of the lcd screen and is what's makes your "touch" control the phone.

To remove the panel, you will need to use a heat gun to heat up the tape holding the panel to the phone shell. One it is nice and gooey, use your non marring tool to pry the panel from the phone, making sure to have the flex cable disconnected from the main board.

To install, clean up the shell and then apply your digitizer tape to the shell, run the flex cable through the opening, and then press the digitizer down onto the shell. Put the phone back together and you're up and running. The first video link  posted above is exactly what you should follow. Its the same for almost every phone.

To separate the front glass from the digitizer on a Samsung Galaxy S is not possible.

These are put together the exact same way the iPhone 4's are. You cannot and repeat, cannot separate the two from each other without something scratching or breaking. I've replaced 100's of cell phone display's and can tell you first hand that if your going to do this and expect a like new phone look when your done, buy the assembly. They sell just the glass on ebay yes, but what they dont tell you is that the adhesive is applied with a special machine that quickly applies a set amount of special clear adhesive and mends the two pieces within a certain timeframe and with perfect pressure. These pieces were never meant to be taken apart. The reason these people on ebay sell you the glass for so cheap and the assembly for a lot more is because they know that you'll buy the cheap one first then end up buying the assembly when things go south. Take it from someone who's been there already. 

This Will Help.

Thanks.

Laptop Wireless Network Issue

No Wifi Network On Laptop

Acer Aspire 5570 laptop will no longer find our wireless network or pick up any others in the area...we checked the front switch and wireless is enabled...also tried the function F3 key and again, wireless is "on". Any other suggestions?

Either the wireless adapter is not turned on, or its not installed properly, what I mean is, while it probably is properly in its place and not disconnected from the computers mainboard, it could have a driver problem. 

You could check on that by right clicking on your my computer or computer icon on your desktop or find it from the start menu and right click on it. Select Manage from the list, from the management window, click on device manager on the left side.

Now on the right side the device manager should be open, from there look / open 'network adapters' and or look for any devices for ? or ! or X mark over them, these all would indicate a problem or that the device is disabled.

If there is a red X that means that the device is disabled right click on that device and select enable and your problem should be solved.

if its a ? mark right click on it and select properties from the new window that opens read the status message and post it to me here and I can give you further instructions.

If its anything else or if its not listed, or if it is listed, just post here and lets see what we can do.

I followed your instruction and in the Device Manager under Network Adapters both the following options were marked with an ! 1. Intel (R) PRO/Wireless 3945 ABG Network Connection 2. isatap.ed.shawcable.net The message for #1 noted above was "Windows cannot load the device driver for hardware. The driver may be corrupt or missing (code 39) Message for #2 noted above was again that Windows could not load the driver (code 31). "

Right click on the device and select uninstall, restart the computer, the device should get installed again automatically if not we need to download the drivers from acer website, let me know how it goes.

SOLVED: I downloaded the drivers and it is up and running. Thanks!

"INSERT SIM" Error Message

No Sim OR Insert Sim Message

WHEN I PUT MY SIM CARD IN THE PHONE IT STILL TELLS ME TO INSERT SIM

Your card might be a little dirty and needs cleaning in the metallic parts where it connects to your phone. If your card is too old it might need to be replaced by your phone company.

Try and insert another SIM from a friend and see if it works. Also please try to insert YOUR SIM in another phone and see if it is OK. 

If it works in another phone then the problem might be with your phone's connectors.

Apple Iphone Insert sim card

Where To Insert Sim Card

How do i take or insert my sim card into phone

i don't know where is the place to insert the sim card in the iphone can u help me please ?

Go to apple support http://support.apple.com/kb/HT1438

On the top of your iphone next to the power button with a slot with a very small hole, there are two holes, one is the bigger one and the small one. 

Use a paper pin and push the small hole, some might need to use more pressure than the other, that should pop out the existing sim and u can put urs in.

Http://crave.cnet.com/8301-1_105-9738138...

Find your solution from the list,
Apple Iphone Smartphone
Codes:

• Unlock Code,
• Password,
• Puk Code,
• Lock Code,
• Other Codes.

Software & Hardware Problems

• Software Problems (Hang, Youtube etc.)
• Hardware Problems (Display, Charging etc.)

Find Your Solutions for Apple Products:
Apple Iphone 3GApple iPod Touch Digital Media Player

YOUR SOLUTION FROM APPLE.

HERE IS YOUR SOLUTION

www.apple.com/iphone/prob237ji32/solution

Here is a site that shows how to do this:

http://freeiphoner.com/att-blackberry-8800-sim-card-installation/

Apple iphone unlock Code

How To Unlock Apple Iphone

I need an unlocking code for an apple iphone connected to orange. i don't have an orange sim card either.

Heres the service you need to use:

IPHONE ORANGE & T-MOBILE FACTORY UNLOCK

http://shop.ebay.co.uk/e-unlocks/m.html?_trksid=p4340.l2562


You can get the unlock code for your iphone mobile, through this site http://www.mobileunlocksolutions.com/apple/rs1wp8/


It provides the easy instructions and some new methods for unlocking mobile phones.


IPhone's don't have unlock codes. You need unlock software, it's free so never pay for it.

http://www.iclarified.com/entry/index.php?enid=2311

If your iPhone has firmware version 3.1.3 you can't unlock it yet. If it's lower version follow the iclarified website

How to unlock iphone 3gs

Iphone Unlock Code

I need to unlock my iphone to use it on t-mobile.

Hi, the best option is to use a carrier authorized unlock, check here if your current network is supported for unlocking: 
http://www.fastgsm.com/en/apple/apple/apple-iphone-3gs/unlock/country-network

If you need to unlock Apple Iphone 3gs,Use Remote unlock service.You can get remote unlock service fromwww.mobileunlocksolutions.com
To get remote unlock service, you have to provide the country and network in which it is currently locked,IMEI number.Then get unlock and unlock it.

The default phones code is 12345 or 00000 u can use it 

Default 4 Digit user code: 1234 or 0000

Default 6 Digit Security code: 123456 or 000000

Type *#06# at the mobile screen to know IMEI no of your mobile.

send the IMEI no to the service provider and they will reply you with unlocking code.

IF Problem not Solved 

You need to install  New Software in the Phone.

If For puk & pin cod problem 

You Go To Service & Sim Office and Get The Puk code And Pin code From Office oprator

Enter The Puk code and Yes

Enter The pin code and Yes

The correct Puk code will Open the locked cell phone and Problem will Quickly Solved.

SamSung Camera Photos Black & White To Color

Samsung Camera Problem

Samsung 105 camera was in wrong mode and photos were taken in b&w. How to convert back to color?

Sorry, there isn't a way. Once the photo was stored as a black-and-white JPEG file, all the color information was discarded.
When you save your actual photo file,you have to save in color mode.There is a option.If you choose black & white then you cannot do anything.

Cell Phone locked , PUK Code

Cell Phone PUK Code

I have my cell phone blocked, appears here puk. I write my pin and the cell describe that it is incorrect, I can not open my cell phone?


Please contact your cellular service provider to get the PUK code for your phone.

Phone Up Customer Services And See What They Can Do.

Your nokia 6020 doesn't have problem. It's your sim card. If you still have your simcard packaging, the PUK code is written their inside it's brochure. Or you can also go to your mobile phone network and ask its PUK code. Or simply buy a new simcard with the same network company.

PLEASE NOTE: I took it to my provider and they had to give me a new SIM card and it fixed the problem. But you lose whatever is saved on the original SIM card.

PUK code can be given only by your service provider which is specific for each and every mobile number.
Contact your sim customer care department over phone. Its free of cost to get the pin or puk no. If you cant contact through your phone get some other phone and contact them.
Go to the nearest service outlet of your service provider they can also help you. 
There is no other way than the above procedure only your service provider can give it nobody else in this world nor any software. 



PROBLEM SOLVED:-
Testimonial: "Thank you ever so much for your help. I have just phoned my service provider. Undertook all the necessary security checks and then they unblocked it."

Facebook not loading

Facebook not loading 

May be facebook server is down.
Try in different search engine.
Many a times facebook will not load in Google chrome but will run start in Opera or in yahoo search engine.

Also try this solutions :-

Force a full refresh for the site. This can be achieved by pressing CTRL + F5 keys at the same time on your favourite browser Firefox, Chrome, Explorer,
Try other related alternative urls such as fb.com
Clear the temporary cache and cookies on your browser then try loading and see.

Or it can be DNS server related issue.
Change your DNS server to your ISP's suggested DNS, or select for automatically detect it. And then check.It will work.

How to clear cookies:
Clear the cache and the cookies from sites that cause problems.

"Clear the Cache":

Tools > Options > Advanced > Network > Cached Web Content: "Clear Now"
"Remove Cookies" from sites causing problems.

Or the other option is try after few hours.Many a times its site maintenance issue.

Thanks.
For more problem keep updated.

Volvo:ABS control module?

You will have to scan the vehicle and see what the code is first, the code tells what are the failure has occurred  Volvo has had some problems with the abs hydraulic systems over the years, so that could be it. Whenever the anti-lock brake light is on it is in fail safe mode and the anti lock feature will not work. It probably is not a fuse problem, but should check all of them anyway. You can replace the module yourself, but it may have to be programmed at the dealer if it is the electrical part and not the hydraulic unit. It really needs to be scanned first. 

See the Abs module location diagram:

4/16 ABS control module
8/15 Hydraulic unit ABS

Anti-lock Brake Systems or ABS is an integral part of the safety of your car. Stopping a car on a slippery surface or in a panic situation can cause us to quickly appreciate ABS. These systems work with the aide of sensors at the wheels, computers and control modules. ABS allows us to slow and stop a car in the event the tires lose traction with the ground no matter the surface or conditions.

When the ABS system does not work properly we are not reaping the full advantage of a major safety system. To ensure you are getting the most out of this feature, make sure your TRACS or ABS light is off.

----------

Click on this link below,for more details.To turn your abs light off:---

http://www.ipdusa.com/Volvo-S70V70-P80/New-Products/ABS-Control-Module/p-128-813-2216/

---------------

If your abs module is checked faulty,then to get it repaired.Please click on the link below:---

http://home.earthlink.net/~vicrocha/Volvo_Parts/Volvo_ABS_FAQ.htm

-------------

How to replace IAC valve

See the diagram shown below for removal of iac valve


1. Remove the idle air control (IAC) valve connector.
2. Remove the IAC valve attaching screws .
NOTE: If the IAC valve has been in service: DO NOT push or pull on the IAC valve pintle. The force required to move the pintle may damage the
threads on the worm drive. Also, DO NOT soak the IAC valve in any liquid cleaner or solvent, as damage may result.
3. Remove the IAC valve assembly .
^ Clean the IAC valve O-ring sealing surface, the pintle valve seat, and the air passage.
^ The IAC valve may be cleaned. Use a shop towel or parts cleaning brush to remove any heavy deposits.
^ Any shiny spots on the pintle or seat are normal and do not indicate misalignment or a bent pintle shaft.
^ If the air passage have heavy deposits, remove the throttle body for a complete cleaning.
^ Inspect the IAC valve O-ring for cuts, cracks, or distortion. Replace the O-rings if necessary.
^ When installing a new IAC valve, be sure to replace the valve with an identical part. The IAC valve pintle shape and diameter are designed
for a specific application.

This procedure is only for installing a new IAC valve.
IMPORTANT: If installing a new IAC valve, replace the IAC valve with an identical part. The IAC valve pintle shape and diameter are designed
for the specific application.
Measure the distance between tip of the IAC valve pintle and the mounting flange.
If the distance is more than 28 mm (1.1 in), use finger pressure to slowly retract the pintle. The force required to retract the pintle of a new valve will
not cause damage to the valve.

INSTALLATION PROCEDURE:--------
1. Lubricate the IAC valve O-ring (3) with clean engine oil.
2. Install the IAC valve assembly (2).
NOTE: Refer to Fastener Notice in Service Precautions.
3. Install the IAC valve attaching screws (1).
Tighten
Tighten the screws to 3.0 N.m (27 lb in).
4. Reconnect the IAC connector.
5. Use the following procedure to reset the IAC valve pintle position:
5.1. Turn ON the ignition, leaving the engine OFF.
5.2. Turn OFF the ignition for 10 seconds.
5.3. Start the engine and verify the correct idle operation.

how to remove the glass top of a Frigidaire slide in oven/ cooktop?

Frigidaire Glass Cooktop



Here is detail from the service manual, to help you get through this repair,

How to access the control panel
•Remove the screw on each side.

•Remove the two screws under

the console.

•Pull down the console.

Remove the screw on both sides of the console.

How to reach the cooktop
Surface Elements

•Remove the control panel.

•Remove the four screws on the

front on the burner box (two on
both side).
•Pull up on the entire burner box

and in order reach the surface
elements, just flip over the

burner box.

•Unscrew the burner box from all

sides.

•Remove the burner box from the

glass top.

• Remove

the retainer bar by

applying pressure to the extremity

and pulling the anchorage away from the retainer bar in order to
free the surface element.There is no need to unplug all the elements

upon replacing the glass cooktop.

Error Code E27 on canon Mp 150 printer

How to clear E27 Code on canon Mp 150 printer?

Procedure as follows ---------------
1) With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in orange and green, starting with orange.)note: press 4 times for waste ink counter reset. "

The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print (auto teste)
2 times Green EEPROM print (dados da EEPROM)
3 times Orange EEPROM reset (EEPROM reset)
4 times Green Waste ink counter reset (Absorvente reset).

Maytag washing machine shows error code f-01?

washer error code f-01

We have the washer like 3 years and the F-01 error kept showing irregularly since one year ago - just after the warranty expiration. Usually unpluging the washer from the power supply solved the problem, sometimes immediately, but mostly overnight. When we moved from flat to country house, the problems frequency slightly increased. Till last couple of days it was still bearable. But in the recent days the error didn't even show up, and the motor was not turning at all. Just the pump was pumping the water in and out, so the program got hanging somewhere. So resolution became necessary. I've contacted tow servicemen yesterday, but none of them answered yet - well it's weekend. But as usually, when you ask for help, you'd find it on your own right after. So I decided to look at it myself.

- unplugged the washer power supply, closed the water
- unscrewed two screws that hold the control panel
- removed the panel - you need the lid to be semi-opened
- (re-conected all connectors to fix any possible oxidation or unpluging - then tried the washer, but problem persisted)
- unscrewed all screws that hold the side cover - only the right one had actually been necessary (when standing in front of the washer)
- unscrewed all four screws hidden under the bottom cover in the front of the washer that hides also the filter (those still hold the side cover)
- unscrewed two more screws at the top back of the washer - they hold the circuit board to the washer body - it needs to be loose
- by pulling the top side of the washer up by the lid and pushing the side cover away "to the back" (with a screwdriver), see how the side cover is held by the top, remove the side cover
- observed the motor and immediately saw heavy corrosion at the ground connection (yellow-green wire) at the motor board and possible slight oxidation at one other connetion of the black wire
- using sand paper and screwdriver I've cleaned the contact together with the connector and tried the washer - still no effect
- cleaned the black wire connection with the same way
- tried the washer (spinning program) and - voila! It works!
- tried unplugging the black wire and running the spinning program - both the motor AND the pump didn't start

So, it looks to me that the problem was in an oxidation of the black wire connection - that is apparently a power supply for both the pump and the motor, that caused insufficient voltage and thus a power for the motor but probably still enough for the pump. The randomness of the problem was probably caused by humidity in the room and maybe some more factors - the washer is actually opened from the bottom so when I test the washer more times and see this as a solution, I'll probably cover the connetors with silicon to avoid corrosion or oxidation in the future.

Here are also some tips for putting all together:

When removing the side cover something fell from it inside. It was a plastic lath that is placed on the nearer edge of the cover and fits both onto the edge of the cover and the adjacent edge of the washer. It's a bit tricky to put it all back plus there is a plastic piece at the bottom of the side cover that is fixed there also very loosely and keeps falling inside when srewing the filter side screws - but this can be fixed with pliers adjusting the edge of the side cover to make the plastic to fit there tightly

---
So if you are a bit technical, try this before calling the service. It might help. And also you'll know your washer a bit more.

Car Recall: 2000 Ford E350 Econoline converted van.

Vehicle Recall

2000 Ford E350 Econoline converted van.

Recall ID # 23114 - EQUIPMENT ADAPTIVE

Recall Date:

NOV 26, 2004

Model Affected:

2000 Ford E-350 Econoline

Summary:

ON CERTAIN VANS EQUIPPED WITH SURE-LOK WHEELCHAIR SECUREMENT SYSTEMS, THE SPROCKET TEETH OF THE RETRACTOR ASSEMBLY IS OUT OF ALIGNMENT.

Consequences:

IN THE EVENT OF A VEHICLE CRASH, THE WHEELCHAIR MAY NOT BE ADEQUATELY SECURED POSSIBLY RESULTING IN INJURIES TO A WHEELCHAIR OCCUPANT.

Remedy:

DEALERS WILL INSPECT AND REPLACE THE WHEELCHAIR SECUREMENT RETRACTORS AS NECESSARY. SURE-LOK WILL HANDLE THE REPAIRS FOR THIS CAMPAIGN. OWNERS SHOULD CONTACT SURE-LOCK AT 1-908-231-1804 OR MOBILITYWORKS AT 1-800-769-8267.

Potential Units Affected:

1660

Notes:

MOBILITY WORKS

Read more: Regarding this recall issue

http://www.motortrend.com/cars/2000/ford/e_350_econoline/recalls/index.html#ixzz1Dlo6QyVb

Philips gogear SA6045: Loading screen appears and shuts off at 35%.

PHILIPS GO GEAR

The philips gogear SA6045, loading screen appears and shuts off at 35%?

There are certain things to be tried to resolve the problem are as follows :---

Reset the player using the pinhole. If it freezes again, you need to update the firmware to resolve the issue permanently.

To update the firmware correctly:
Download the newest version of the Philips Device Manager:
www.usasupport.philips.com - change your country/language as needed
Enter in your exact model #
Click on the link for your exact model #
Click on the Software & Drivers section
Click on "Firmware Upgrade Software"
Install the new Device Manager
Open and run the "Update" tab